Making a (very) home-made strop

From Shave Library
Jump to: navigation, search

Last time I made some 'roo strops I promised Robin (BeBerlin) that I would put together a little photo tutorial if I were to ever do it again. Well, I have done it again and, true to my word, here is a little photo tutorial.

How To Make a (Very) Home-made Strop: A life in pictures[edit | edit source]

Get some leather[edit | edit source]

The choice is yours really. If you are only going to make a strop for yourself you probably just want to get hold of a nice single piece from a leather retailer (perhaps already cut to size and maybe a bit larger than you want - see below). I on the other hand want to make my strops out of Kangaroo, and as far as I know you cannot just buy a single piece. So I have bought a couple of hides - both veg tanned, one natural colouring and one dyed chocolate.

Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0395.jpg

Get the stuff[edit | edit source]

  1. Straight edges: a metal ruler and a set square;
  2. A Stanley knife (for cutting with);
  3. A hammer to really get those corners at right-angles with a gentle tap (just kidding - for punching holes and setting rivets);
  4. A small anvil (solid surface for hole punching and rivet setting);
  5. Leather punch of a size appropriate to your rivets;
  6. A rivet peener;
  7. Rivets;
  8. Something with which to attach your strop to the wall, door etc (I use welded D-rings, but this is just one option).

Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0396.jpg Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0399.jpg

Cut the Leather[edit | edit source]

The size that you make your strop will be a personal choice. For ease, I make mine the width of the ruler (about 2.4") and approx 19" in length. A word of warning (gained through bitter, bitter experience): measure 5 times and cut once. Make sure you get the cut right the first time, because (unless you are a better man than I) going back to "trim it up" nearly always ends in wobbly edges and looks like rubbish. Make sure everything is square or again it will look like rubbish. Keep the leftover bits of leather, they can come in handy.

Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0400.jpg Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0401.jpg Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0402.jpg

Little Square bits[edit | edit source]

In this step I cut the little square pieces (from the leftover leather) that I use to attach the D-ring, via rivets, to the main body of the strop. I try to make these the same width as the strop.

Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0407.jpg

Triangles in the little square bits[edit | edit source]

My D-rings are narrower than the little square bits are wide. Therefore I need to cut triangles out of the leather so that the rings will fit properly. Measure this bit very carefully, as even a small misalignment can cause things to become crooked.

Measure the width of the straight part of the D-ring. Then, mark off the small piece of leather so that this space is centered (in both horizontal and vertical directions) after you cut out the triangular piece of leather from each side.

Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0408.jpg

Hole Punching[edit | edit source]

Now that you have the main strop body and the small piece of leather cut out, measure (I do not) evenly the places where you want to rivet the two pieces of leather together and punch the holes with the leather punch. Again, be careful here because you cannot put the holes back if you misalign them.

Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0410.jpg Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0411.jpg

Attach D-ring with Rivets[edit | edit source]

Now all you have to do is put the D-ring onto the small bit of leather and attach that using the rivets. Rivets have two sides - it probably looks best if the domed head (female part) of the rivet is facing the treated side of the strop. Just whack in the male part, place the dome on top, get a nice secure surface, and use the rivet peening tool and hammer to gently but firmly secure the pieces.

Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0412.jpg Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0414.jpg

Sit back and admire your efforts[edit | edit source]

That is it, all done. I attach a piece of kangaroo lace to the D-ring so that it is easier to attach the strop to things in the bathroom like towel racks and so forth.

Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0416.jpg Jimbo - How To Make a (Very) Home-made Strop - Jimbo - How To Make a (Very) Home-made Strop - dscn0417.jpg

Now go forth and enjoy your new strop, with the relish that only comes when the fruits are borne from your own efforts!

Acknowledgements[edit | edit source]

This article was originally posted by Jimbo[1]

References[edit | edit source]