Difference between revisions of "Easily make a pasted balsa strop"
Line 25: | Line 25: | ||
<gallery Caption:"Making The Slartibartfast Pasted Strop" widths="300px" heights="180px" perrow="2"> | <gallery Caption:"Making The Slartibartfast Pasted Strop" widths="300px" heights="180px" perrow="2"> | ||
− | Materials I used | + | Image:Pasted_balsa_strop_by_slart_001.JPG|Materials I used |
− | Image: | + | Image:Pasted_balsa_strop_by_slart_002.JPG|I use clamps, a heavy object will work too once you glue to 2 pieces together |
− | I use clamps, a heavy object will work too once you glue to 2 pieces together | + | Image:Pasted_balsa_strop_by_slart_003.JPG|Make a Grid on the balsa so you can lap it flat. |
− | Image: | + | Image:Pasted_balsa_strop_by_slart_004.JPG|Use a figure 8 or x-pattern until the marks are gone. You may want to wipe down the balsa with a damp towel afterward. |
− | Make a Grid on the balsa so you can lap it flat. | + | Image:Pasted_balsa_strop_by_slart_005.JPG|Mix the Chromium Oxide powder with some mineral oil |
− | Image: | + | Image:Pasted_balsa_strop_by_slart_006.JPG|Much Easier to spread now |
− | Use a figure 8 or x-pattern until the marks are gone. You may want to wipe down the balsa with a damp towel afterward. | + | Image:Pasted_balsa_strop_by_slart_007.JPG|Draw an X pattern and then spread |
− | Image: | + | Image:Pasted_balsa_strop_by_slart_008.JPG|What it looks like spread out. Note: this may be a little thick.... |
− | Mix the Chromium Oxide powder with some mineral oil | + | Image:Pasted_balsa_strop_by_slart_009.JPG|Why I wear gloves when applying CrO |
− | Image: | + | Image:Slart_Strop10.JPG|Mark your pasted strop to avoid confusion later |
− | Much Easier to spread now | ||
− | Image: | ||
− | Draw an X pattern and then spread | ||
− | Image: | ||
− | What it looks like spread out. Note: this may be a little thick.... | ||
− | Image: | ||
− | Why I wear gloves when applying CrO | ||
− | Image: | ||
− | Mark your pasted strop to avoid confusion later | ||
− | |||
</gallery> | </gallery> |
Revision as of 23:12, 13 March 2009
Originally posted by backpackerx.[1]
Just finished making a homemade balsa strop and thought I'd post here since it's so easy. I did this because I'm a newbie who has blown the budget for a while and can't buy one and also because it's so dead easy that even I, who have zero craftsman abilities, could do. Hopefully I can figure out how to get the pictures to post on here.
This literally requires 6 things. A porch or stair spindle from Home Depot ($2), a piece of Balsa from a craft store ($3), something to make one small 2" straight cut, a utility knife, glue, and some sand paper. I saw the spindle at Home Depot and noticed that if cut in half it would make a great base for the paddle and had a nice looking handle built right in! I simply cut the spindle in half, cut some balsa to fit the end, glued it on and sanded it to lap it flat. Cost about $5 and took about 10 minutes. See results below. The last picture is what the spindle looks like together.
The Slartibartfast Pasted Strop
Materials needed: Some type of solid backer, i cut a piece of 12x12 tile i had laying around.
Balsa: You can find this at most hobby stores.
Some kind of glue
Clamps or something heavy to set on top once everything is glued down.