This article was originally posted as [1] by gssixgun
This is a thread that I have been wanting to do for awhile, but these things take time, and half the time when I go out to the shop I forget the camera....
This restore I finally got pics of just about the whole process so I figured I would do a complete restore in pictures....
This is a C.W.Dahlgren Eskilstuna Medalier Chicago 1893 the proof marks show 1886, 1888, 1881, 1878 the frameback is stamped Sanvik Bessamer Stal.....
The scales are Spalted Apple, the wedge is Brown Ebony....
Nickel Silver pins and SS washers...
This one has 15 coats of Satin Wipe on Poly for the finish...
Starting out the razor has a very small touch of rust and some patina, the scales are shot...
- The Process in Pictures
Starting out, the razor has a very small touch of rust and some patina, the scales are shot...
I have the wood cut at 3/16 thickness...
I put the wood together using rubber cement, make sure you leave the pattern that you want to show, to the outside...
I usually leave the wood in the vise and clamped up overnight
The razor all broken down, save everything !!!! you might need it....
While I am working on the scales the blade will be spinning along, I use the Turtle Wax Rubbing compound in with the walnut media (re-fresh this about every 4 months) after 48 hours I will check the blade and use 800 grit sandpaper to take off any remaining spots and let it spin some more After that it will go through the same thing with Corncob media and Turtle Wax Polishing compound.... Keep in mind this will not take off rust or pitting....
I use the old set of scales to get a rough idea of the size, and the curves I will need for the new scales
Note here, See how the scale is covering that veining on the wood ??? I want that to show in the new scales
You don't have to do this but it does give you a starting point...
I rough cut the scales out of the blanks...
Leaving plenty of wood to play with shapes that I might want....
These rough cuts then move to a bench sander, and I work out the shape I want for the scales, freehand....
My rule on scale design in general.... Let the wood do the talking, fancy wood?? Simple scales.... Simple wood???? fancy scales......
These are still oversized, but they are getting close to what I want now...
Just sizing out the razor to the scales...
The wedge marked for cuts
Scroll saws are a handy tool here
The wedge gets sized and sanded to the right angle...
The wedge gets sized and sanded to the right angle...
The wedge gets sized and sanded to the right angle...
The moment of truth !!!!! when you drill the pivot hole, you ARE committed, so make sure you do it right.... If you mess up here it's back to the beginning....
Freshly drilled pivot hole
Mark the razor swing angle so you know where the wedge is going to fit in, and where the wedge hole goes....
I have already drilled the wedge hole in the scales
I drill the hole through the wedge this way, as it never misses but that your choice....
Ok some pics didn't turn out, but needless to say all ya missed was a lot of sanding, the scales were taken apart and sanded, shaped, and thinned down....
Testing the fit and function here using adjustable pins....
Look close here the wedge is hitting the razor, it needs some more fitting...
Ahhhhhh there we go about 1/8 inch clearance and everything fits together the right way now....
Make sure everything moves right and fits right....
Time to finish the wedge, note the "Mock Up Tang" in the scales now, because I am taking it back to the bench sander to fit the wedge...
Done and ready to be finished....
The scales are finished and ready to become a complete razor, How and what you use as a finish is totally up to you, try different things to get the look you want... (How I prep the wood is the only part of this, I can't actually share, as parts of it are proprietory to my Rifle Stocks) the wipe on Poly's from minwax are working very well on the razors....
Pins go in from the show side to the reverse side...
I always pin the wedge first then the middle (if applicable) and finally the pivot...
Again the pins go in on the show side..
Don't forget the bearing washers if you are using them...
Bearing washer, razor, bearing washer....
Don't mess up now, this is the end of the journey, be extra careful peening the pivot pin, if you leave this pin to long, you stand the risk of a bent pin, to short you have to make a new pin...
A completed razor, some final hand polishing on the blade, then it is ready for the hones......
Q&A
Q. Glen, as usual, awesome job! I'd like to know a little more about how you go about doing the wipe-on poly with the inside of the scales and the wedge. Do you coat the entire inside of the scale (once or more)? Do you coat the wedge prior to installation? Do you pin the wedge end and then coat all of it as a unit?
A. First thing I do is 3 coats of finish on the inside, after that really dries, I put two pieces of double side tape on the edge of what ever mailing box is in the room at the time.... I stick the scales to the box where the wedge would go, and then start the process of doing the outside coats with a box to hang unto and the scales securely attached to it.... This is for wipe on finishes....
As you can see this box gets used alot....
For spray on finishes, again I do at least 3 coats on the inside, before I get the outside started.. I made some holders for the scales for spray finishes.. Just a piece of wood and some stiff wire...
As to the wedge end ??? Yes the wedge is coated to as I do the outside, I do 3-5 coats depending on the finish I am using, this is for wood/bone wedges...